Waiting for time

[sg1ghost]

Hi, just flashed nokia2 with commando 9.25 loaded keys roms etc etc done it hundred times just want to know if my tuner is broke ???????

ber: 107170
snr: 62451
sig: 42919
bitrate: 0

with feed, ethernet and null conected

debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID 7a gtxID 0b
debug: fpID 5a dsID 01-64.43.19.07.00.00-54
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0036

will verify ELF image, start= 0x800000, size= 162920
verify sig: 262
Branching to 0x40000


U-Boot 1.2.0 (Tuxbox) (Nov 5 2007 - 10:24:09)

CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: .. done.
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
### FS (squashfs) loading 'vmlinuz' to 0x100000
### FS load complete: 669732 bytes loaded to 0x100000
.................................................. ............. done
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 669668 Bytes = 654 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.35.3-dbox2 (nitr8@jijina.nfye.com) (gcc version 3.4.4) #1 Mon
Nov 5 10:25:31 GMT 2007
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock2 rootfstype=squashfs
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30828k available (1144k kernel code, 336k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:1d:d0:08
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "FLFS (U-Boot)"
0x00040000-0x006a0000 : "root (squashfs)"
0x006a0000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v1.7.2 (2007-11-05 16:35:30 GMT)
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
dboxide: $Id: main.c,v 1.11 2007/08/07 09:02:15 dbt Exp $
ide: late registration of driver.
dboxide: activating cs2
dboxide: address space of IDE-Interface is at: 0xc3890000
dboxide: probing dbox2 IDE CPLD: walking bit test failed: 0xfffffffe != 0xfbffff
dc
dboxide: no valid IDE-Interface detected
Journalled Block Device driver loaded
SGI XFS with no debug enabled
mount: mounting /dev/ide/host0/bus0/target0/lun0/part2 on /hdd failed: No such f
ile or directory
route: SIOCADDRT: Network is unreachable
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
Detected STB:
Vendor: Nokia
Model: D-BOX2
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
DVB: VES1820(0): pwm=0x48
DVB: registering frontend 0:0 (VES1820 based DVB-C frontend)...
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
avia_av: $Id: avia_av_core.c,v 1.99 2006/01/08 21:36:22 carjay Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.15 2007/07/29 18:14:12 papst Exp $
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... GTX
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_ucode: loaded ucode v001A
avia_gt_ucode: ucode section filters disabled.
avia_gt_core: masking unhandled irq reg 0 bit 6
avia_gt_core: masking unhandled irq reg 0 bit 7
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
/etc/init.d/rcS: line 253: cannot create /etc/issue.net: Read-only file system
Starting the automounter

Please press Enter to activate this console. avia_oss: IOCTL: SNDCTL_DSP_SPEED (
arg=44100)
avia_gt_pcm_set_rate(44100)
$Id: sectionsd.cpp,v 1.249 2007/10/30 08:48:23 seife Exp $
[sectionsd] Caching max 6000 events
[sectionsd] Caching 14 days
[sectionsd] Caching 6 hours Extended Text
[sectionsd] Events are old 60min after their end time
$Id: zapit.cpp,v 1.402 2007/07/22 14:36:42 dbluelle Exp $
[frontend] uncommitted_switch_mode 0
/tmp/currentservices.xml: No such file or directory
$Id: controld.cpp,v 1.127 2007/07/01 08:40:13 dbluelle Exp $

[controld] Boxtype detected: (1, Nokia D-BOX2)
[controld]: ROUTEVIDEO v1 = 5 a1 = 1 v2 = 1 a2 = 1 v3 = 0 a3 = 1 fblk=1
[controld] setting VideoFormat to auto
[yhttpd] Webserver nhttpd/3.1.3 (yhttpd_core/1.2.0)
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)
[LCDFONT] Intializing font cache...
[yhttpd] Webserver starting...
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[dmx.cpp:read:184] read(fd, buf, n): Connection timed out
^A[sectionsd] getUTC: read: Connection timed out
^A^A^A

any ideas any1
im trying this box in the same place i try all my boxes m8, im litterally moving my own box out the way to try it....

[gaz]

Hi

Dont know what the rest of the log means but your snr and sig levels are fine but ber is high but I I have seen them working with high bers before.

I assume you have set location and checked thet netid and your symb rate is correct for your area and have you tried changing ucodes.

There is a test you can do that might determine tuner is working or not.

Someone posted this test elsewhere dont know who.

If you can, take a normal aerial cable and plug the RF out on the dbox into the aerial socket on your TV.. If you tune in the analog channels on your TV you should get some FTA channels, i.e. bbc, itv, etc. if you don't get any channels the tuner is gubbed!

Hope this helps

Regards

[sg1ghost]

hello m8, done test got nowt

YouTube - Nokia Tuner repair

YouTube - Nokia Tuner repair

http://uk.rs-online.com/web/search/s...94953929&Nty=1
77pence....

http://www.avatarhosting.net/7312
going down this route, will post results when fitted :fingerscrossed:

[gaz]

Hi

Then according to test tuner is goosed but wait to see if someone else has any other ideas.

Reagrds

[sg1ghost]

i ok m8, dont think theres anything else any1 can offer me to try i know the software route is sound, but any ideas welcome.....

when i do a full scan i do find the 303 transponders but find no chanells, kinda hope it is this little transistor i collect it tomorrow and ill fit it then great little tut video.

[gaz]

Hi

Let us no if this works for you, I tried this on one a while back and didnt work for me but thats probably down to me lol.

One thing did you ftp your own services to the box. or have you only tried the scanning and its not finding any channels.

Regards

[sg1ghost]

always use my own services m8, but i did try a full scan also and nothing, getting a multi meter today coz in the dbox bible this is covered :-


You need the following currents on a cable tuner





I will write more details about the origin of these currents and more details about them further below.


You may find that even you can check for all these currents you still get channel not available or Error UD4 (Betanova). On Cable boxes the Transistor BFG94 can be the cause of this fault. This transistor is located within the Input amplifier and is supposed to amplify the incoming signal. Please see the attached Picture left and the layout is similar within the Dbox tuner. The example picture is a standard usage for this kind of transistor (datasheet).
copied from the dbox bible

[gaz]

Hi

Erm very interesting I didnt go that far I just changed the bfg94 transistor and then couldnt be bothered after that.

Regards

[wullboy]

Originally Posted by sg1ghost

i ok m8, dont think theres anything else any1 can offer me to try i know the software route is sound, but any ideas welcome.....

when i do a full scan i do find the 303 transponders but find no chanells, kinda hope it is this little transistor i collect it tomorrow and ill fit it then great little tut video.

This is not as easy as it looks m8, i bought a duff box from ebay, Yea, i new it was a duff box as the guy said so in his auction, he gave me the transistor that was needed to fix the problem as he saw it, when i looked into the tuner i could see that someone had already fitted a new trannie, so i took the box to a work collaegue who is an electronic engineer who has worked on digital boards for some twenty years, when he looked at the tuner he could see there was heat damage to the trannie,so he replaced the trannie with the new one, and tided up the damage that was done with excess heat that had been put on the part, so m8 you really need a thermostatic soldering iron with a very, very thin rod on the end, as it is very easy to damage the trannie and suroundng components, CHEERS

[sg1ghost]

Well iv fitted the new transistor and Heypresto it didnt work

Iv played about with it enough its goin on spares/repairs...
i tried..