Lincstat.beta7.25 Streaming problem

[Hewoe]

Hi
I have a Sagem 1x dbox to which I have flashed Lincsat.Beta7.25-Full. The image is smooth and works very well, but I have a problem in the form of streaming the output to my pc.

My setup has the dbox connected to a wireless bridge which then relays the signal over my wireless network. Control of the dbox is through the yweb interface. This allows me to watch my dbox in my room even though the box is located in another part of my house.

However since flashing with this image I find that when I run WMP, rather then the stream picking up I get this message instead "The network address could not be used for the operation requested."

I previously had the Sportster 1.73 image and bitcontrol 2.0 on my pc. This configuration worked fine other than Sportster being flaky and prone to freezes, partly the reason I like this newer image so much.

But after going through the various menus I cant seem to find the source of the problem. I'm guessing that it may be a feature that has been dropped since the days of sporster, but it is one I found hugely useful.

I have tried the alternative combination of WingrabTv and Vlc but I find the quality of the stream to be somewhat bitty and not to the same standard of stream as that produced by bitcontrol.

Any assistance would be greatly appreaciated.

[turner123]

i could be wrong but check the ip addys of the proggy you are using that will be set to your old ip of the sportster image and will defo be differant in the lincsat img, if it is a file etc im sure 1 of our devs will be able to assist you further...as for wingrab n vlc i have always found them to be very reliable and quality always smooth...every1 to there own thou

[Hewoe]

Originally Posted by turner123

i could be wrong but check the ip addys of the proggy you are using that will be set to your old ip of the sportster image and will defo be differant in the lincsat img, if it is a file etc im sure 1 of our devs will be able to assist you further...as for wingrab n vlc i have always found them to be very reliable and quality always smooth...every1 to there own thou

I'm not 100% sure which i.p you are refereeing to as with bitcontrol I only need to set the target i.p to be the same as the one set within the network settings page. The rest of my settings are identical between both images. If you are talking about a different internal i.p for the image then how would I access this?

With regards to wingrabTV, i'm just finding the process a bit clumsy as you have to run wingrabtv then load VLC and then finally type the address to stream. Bitcontrol with wmp is a much smoother process, I just double click a link and hey its streaming.

Btw after running wingrabtv the first time, I no longer see any settings pages, and i'm finding the stream a bit stuttery. Is there any way to adjust the performance?

Thanks for your time and help.

[turner123]

goto
dbox button
settings
network
the ip of the bow will be in there m8 ie 192 168 1 110 your program should then be 192 168 1 109... also look at my tut on streaming when i made it i had probs with it crashing every now an then, but then i got a belkin wireless n router and its been 100% ever since not even a stutter or freeze even chanel change works spot on

[Hewoe]

Originally Posted by turner123

goto
dbox button
settings
network
the ip of the bow will be in there m8 ie 192 168 1 110 your program should then be 192 168 1 109... also look at my tut on streaming when i made it i had probs with it crashing every now an then, but then i got a belkin wireless n router and its been 100% ever since not even a stutter or freeze even chanel change works spot on

I've started using DboxTv instead and find it to be the best streaming solution. It has the complete dbox interface streamed within the application. You get bouquets and epg control within the app. You should try it out.

Thanks for your assistance though mate.